[ Avaa Bypassed ]

index_title=Shorewall6 Firewall
index_ecmd=The command $1 was not found on your system. Maybe it is not installed, or the <a href='$2'>module configuration</a> is incorrect.
index_edir=The Shorewall configuration directory $1 was not found on your system. Maybe it is not installed, or the <a href='$2'>module configuration</a> is incorrect.
index_version=Shorewall6 version $1
index_return=list of tables
index_restart=Apply Configuration
index_restartdesc=Click this button to activate the current Shorewall configuration with the <tt>shorewall6 restart</tt> command.
index_refresh=Refresh Configuration
index_refreshdesc=Click this button to activate just the Blacklist and Traffic Shaping tables with the <tt>shorewall6 refresh</tt> command.
index_start=Start Firewall
index_startdesc=Click this button to start Shorewall with the current configuration with the <tt>shorewall6 start</tt> command.
index_clear=Clear Firewall
index_cleardesc=Click this button to clear Shorewall with the <tt>shorewall6 clear</tt> command. This will allow access from all hosts without restriction.
index_stop=Stop Firewall
index_stopdesc=Click this button to shut down Shorewall with the <tt>shorewall6 stop</tt> command. This will block access from all hosts except those in the When Stopped table.
index_status=Show Status
index_statusdesc=Click this button to view Shorewall's tables and rules from the <tt>shorewall6 status</tt> command.
index_dump=Show Dump
index_dumpdesc=Click this button to view Shorewall tracing information from the <tt>shorewall6 dump</tt> command.
index_check=Check Firewall
index_checkdesc=Click this button to have Shorewall validate your firewall configuration with the <tt>shorewall6 check</tt> command.

list_move=Move
list_add=Add
list_auto=Automatic
list_none=None
list_any=Any
list_fw=Firewall
list_other=Other..
list_manual=Manually Edit File
list_manualdesc=Click this button to manually edit the Shorewall file $1, in which the entries above are stored.
list_ecannot=You are not allowed to edit this Shorewall table.
list_delete=Delete Selected

restart_err=Failed to apply configuration
refresh_err=Failed to refresh configuration
start_err=Failed to start firewall
clear_err=Failed to clear firewall
stop_err=Failed to shut down firewall
status_title=Firewall Status
dump_title=Firewall Dump
check_title=Check Firewall
check_ok=.. your firewall configuration looks OK.
check_failed=.. an error was found in your firewall configuration!
check_cmd=Checking configuration ..

zones_title=Network Zones
zones_desc=The zones listed on this page represent different networks reachable from your system. However, the entries here do no actually have any effect on the firewall - instead, they just define zone names and descriptions.
zones_add=Add a new network zone.
zones_none=No network zones have been defined yet.
zones_0=Zone ID
zones_1=Displayed name
zones_2=Description
zones_1new=Parent zone
zones_2new=Zone type
zones_3new=Zone options
zones_4new=Incoming options
zones_5new=Outgoing options
zones_6new=Comment
zones_return=zones list
zones_edit=Edit Network Zone
zones_create=Create Network Zone
zones_header=Network zone details
zones_err=Failed to save network zone
zones_eid=Missing or invalid zone ID
zones_efwid=The zone IDs $FW and fw are reserved for the firewall
zones_ename=Missing or invalid displayed name
zones_edesc=Missing zone description
zones_ipv6=IPv6
zones_ipsec=IPsec
zones_ipsec6=IPsec6
zones_bport=bport
zones_bport6=bport6
zones_firewall=Firewall system
zones_eopts=Invalid zone options
zones_eopts_in=Invalid zone incoming options
zones_eopts_out=Invalid zone outgoing options

policy_title=Default Policies
policy_desc=This page allows you to configure the default actions for traffic between different firewall zones. They can be overridden for particular hosts or types of traffic on the Firewall Rules page.
policy_add=Add a new default policy.
policy_none=No default policies have been defined yet.
policy_0=Source zone
policy_1=Destination zone
policy_2=Policy
policy_3=Syslog level
policy_4=Traffic limit
policy_limit=Limit $1, Burst $2
policy_return=policies list
policy_edit=Edit Default Policy
policy_create=Create Default Policy
policy_header=Default policy details
policy_err=Failed to save default policy
policy_nolog=Logging disabled
policy_ulog=Log to ULOG
policy_efw=&lt;Firewall&gt; can be selected for both the source and destination zones
policy_elimit=Missing or invalid traffic limit number
policy_eburst=Missing or invalid traffic burst number

rules_title=Firewall Rules
rules_desc=This table lists exceptions to the default policies for certain types of traffic, sources or destinations. The chosen action will be applied to packets matching the chosen criteria instead of the default.
rules_add=Add a new firewall rule.
rules_none=No firewall rules have been defined yet.
rules_0=Action
rules_1=Source
rules_1z=Source zone
rules_2=Destination
rules_2z=Destination zone or port
rules_3=Protocol
rules_4=Source ports
rules_5=Destination ports
rules_6=Rate limit
rules_7=User set
rules_hosts=Host <tt>$2</tt> in zone <tt>$1</tt>
rules_zone=Zone <tt>$1</tt>
rules_rport=Port <tt>$1</tt>
rules_related=Related
rules_return=firewall rules list
rules_edit=Edit Firewall Rule
rules_create=Create Firewall Rule
rules_header=Firewall rule details
rules_err=Failed to save firewall rule
rules_log=and log to syslog level
rules_nolog=Don't log
rules_addr=Only hosts in zone with addresses
rules_ranges=Ports or ranges
rules_dnat=Original destination address for DNAT or REDIRECT
rules_dnat_dest=For DNAT or REDIRECT, fill in the new destination address or port here.
rules_dnat_port=For DNAT or REDIRECT, fill in the original destination port here.
rules_esother=Missing or invalid source zone
rules_edother=Missing or invalid destination zone
rules_esinzone=No host addresses entered for source
rules_edinzone=No host addresses entered for destination
rules_esport=No source port names, numbers or ranges entered
rules_edport=No destination port names, numbers or ranges entered
rules_ednat=Original destination address must be a single IP address, two addresses separated by a :, or an exclusion list starting with !
rules_ednat2=An original destination address can only be entered for the DNAT and REDIRECT actions
rules_rate=Rate limit expression
rules_norate=No limit
rules_set=Rule applies to user set
rules_noset=All users
rules_eaction=No action selected
rules_macro=Macro action parameter
rules_none2=None
rules_emacro=Missing or invalid macro parameter

tos_title=Types of Service
tos_desc=This page defines IP service types for particular types of traffic, which can be used to raise or lower their priorities.
tos_add=Add a new type of service.
tos_none=No types of service have been defined yet.
tos_0=Source
tos_0z=Source zone
tos_1=Destination
tos_1z=Destination zone
tos_2=Protocol
tos_3=Source ports
tos_4=Destination ports
tos_5=Type of service
tos_6=Test
tos_return=types of service list
tos_edit=Edit Type of Service
tos_create=Create Type of Service
tos_header=Type of service details
tos_err=Failed to save type of service

interfaces_title=Network Interfaces
interfaces_desc=Each of the network interfaces on your system that you want Shorewall to manage should be listed on this page, and associated with the zone that it is connected to. The loopback interface <tt>lo</tt> must never be listed.
interfaces_add=Add a new network interface.
interfaces_none=No network interfaces have been defined yet.
interfaces_0=Interface
interfaces_1=Zone name
interfaces_2=Options
interfaces_detect=Automatic
interfaces_return=interfaces list
interfaces_edit=Edit Network Interface
interfaces_create=Create Network Interface
interfaces_header=Network interface details
interfaces_err=Failed to save network interface
interfaces_eiface=Missing or invalid interface name
interfaces_ebroad=Missing or invalid broadcast address

masq_title=Masquerading
masq_desc=Entries on this page set up network address translation for traffic routed between some network and a particular interface.
masq_add=Add a new masquerading rule.
masq_none=No masquerading rules have been defined yet.
masq_0=Outgoing interface
masq_1=Network to masquerade
masq_2=SNAT address
masq_3=Restrict to protocol
masq_4=Restrict to ports
masq_5=IPsec options
masq_any=Any protocol
masq_all=All ports
masq_in=<tt>$2</tt> on <tt>$1</tt>
masq_ex=Network on <tt>$1</tt> except <tt>$2</tt>
masq_iface=Network on <tt>$1</tt>
masq_return=masquerading list
masq_edit=Edit Masquerading Rule
masq_create=Create Masquerading Rule
masq_header=Masquerading rule details
masq_err=Failed to save masquerading rule
masq_net=Only for destination
masq_mode0=Subnet address
masq_mode1=Subnet on interface
masq_except=Except for networks
masq_enet=Missing or invalid outgoing interface destination
masq_emnet=Missing or invalid masquerading subnet address
masq_emnete=Empty exception networks list
masq_esnat=Invalid SNAT IP address
masq_eports=Missing or invalid comma-separate list of ports
masq_eipsec=Missing IPsec options

nat_title=Static NAT
nat_desc=The static network address translation entries in this table can be used to set up a 1-1 correspondence between an external address on your firewall and an RFC1918 address of a machine behind your firewall. Static NAT is often used to allow connections to an internal server from outside your network.
nat_add=Add a new static NAT entry.
nat_none=No static NAT entries have been defined yet.
nat_0=External address
nat_1=External interface
nat_2=Internal address
nat_virt=virtual
nat_return=static NAT list
nat_edit=Edit Static NAT
nat_create=Create Static NAT
nat_header=Static NAT entry details
nat_err=Failed to save static NAT entry
nat_all=Active for all hosts?
nat_local=Active for firewall system?
nat_eext=Invalid external IP address
nat_eint=Invalid internal IP address
nat_evirt=Invalid virtual interface number

proxyndp_title=Proxy NDP
proxyndp_desc=This page allows you to configure your system to answer NDP requests for IP addresses other than its own, so that it can forward packets to those addresses to their real destinations.
proxyndp_add=Add a new proxy NDP address.
proxyndp_none=No proxy NDP addresses have been defined yet.
proxyndp_0=Address to NDP
proxyndp_1=Connected to interface
proxyndp_2=External interface
proxyndp_3=Persistent?
proxyndp_return=proxy NDP address list
proxyndp_edit=Edit Proxy NDP Address
proxyndp_create=Create Proxy NDP Address
proxyndp_header=Proxy NDP details
proxyndp_err=Failed to save proxy NDP
proxyndp_have=Route to host exists?
proxyndp_eaddr=Missing or invalid address to NDP
proxyndp_pers=Leave route even when firewall stopped?

routestopped_title=When Stopped
routestopped_desc=By default, when Shorewall is stopped it will deny access from all hosts. This page allows you to define hosts or networks that will still be accessible.
routestopped_add=Add a new stopped address.
routestopped_none=No addresses to be accessible when stopped have been defined yet.
routestopped_0=Interface
routestopped_1=Accessible addresses
routestopped_2=Route options
routestopped_return=stopped address list
routestopped_edit=Edit Stopped Address
routestopped_create=Create Stopped Address
routestopped_header=Stopped address details
routestopped_err=Failed to save stopped address
routestopped_eaddr=No addresses entered
routestopped_all=All addresses
routestopped_list=Listed addresses and networks ..

tunnels_title=VPN Tunnels
tunnels_desc=This page lists VPN tunnels that pass through your firewall, and so must be allowed by the Shorewall configuration.
tunnels_add=Add a new VPN tunnel.
tunnels_none=No VPN tunnels to allow have been defined yet.
tunnels_0=VPN Type
tunnels_1=Zone for interface
tunnels_2=Remote gateway
tunnels_3=Gateway zones
tunnels_gnone=None
tunnels_return=VPN tunnels list
tunnels_edit=Edit VPN Tunnel
tunnels_create=Create VPN Tunnel
tunnels_header=VPN tunnel details
tunnels_err=Failed to save VPN tunnel
tunnels_sel=Gateway IP
tunnels_ipsec=IPsec
tunnels_ipsec:ah=IPsec (with AH)
tunnels_ipsecnat=IPsec with NAT
tunnels_ipsecnat:noah=IPsec with NAT (no AH)
tunnels_gre=GRE
tunnels_l2tp=Layer 2 tunneling (UDP 1701)
tunnels_openvpn=OpenVPN
tunnels_openvpnclient=OpenVPN client on firewall
tunnels_openvpnclient_1=OpenVPN client on firewall, on port..
tunnels_openvpnserver=OpenVPN server on firewall
tunnels_openvpnserver_1=OpenVPN server on firewall, on port..
tunnels_openvpn_l=OpenVPN, on port..
tunnels_generic=Generic
tunnels_generic_l=Generic, for protocol..
tunnels_gsel=Listed zones
tunnels_eopenvpn=Invalid port number for OpenVPN tunnel
tunnels_egeneric=Missing protocol or protocol:port for generic tunnel

hosts_title=Zone Hosts
hosts_desc=This page lists hosts and networks that are part of particular zones. You generally do not need to make any changes to this list.
hosts_add=Add a new zone host.
hosts_none=No zone hosts have been defined yet.
hosts_0=Zone
hosts_1=Interface
hosts_2=IP address or network
hosts_opts=Host options
hosts_return=zone hosts list
hosts_edit=Edit Zone Host
hosts_create=Create Zone Host
hosts_err=Failed to save zone host
hosts_enet=Missing or invalid host address
hosts_header=Zone host details
hosts_routestopped=Route even when firewall is stopped?
hosts_ip=Address or network $1
hosts_mac=MAC address $1
hosts_ipset=IP set $1
hosts_any=Any host

edit_before=Before entry $1
edit_after=After entry $1

blacklist_title=Blacklist Hosts
blacklist_desc=This page lists hosts and services that will be blocked if traffic from them arrives on an interface with the <b>blacklist</b> option set.
blacklist_add=Add a new blacklist host.
blacklist_none=No blacklist hosts have been defined yet.
blacklist_0=Host or network
blacklist_1=Protocol
blacklist_2=Ports
blacklist_any=Any
blacklist_header=Blacklist host details
blacklist_host=Host or network
blacklist_proto=Protocol
blacklist_ports=Port or port list
blacklist_err=Failed to save blacklist host
blacklist_ehost=Missing or invalid host IP address or network address
blacklist_emac=Missing or invalid MAC address
blacklist_eipset=Missing IP set name
blacklist_edit=Edit Blacklist Host
blacklist_create=Create Blacklist Host
blacklist_eproto=Missing or invalid protocol
blacklist_eports=Invalid port number or comma-separated list of ports
blacklist_eports2=Ports can only be specified for the TCP and UDP protocols
blacklist_return=blacklist hosts

providers_title=Additional Routing Providers
providers_desc=This page defines additional routing tables. These are needed if you have connections to more than one ISP or multiple connections to the same ISP, or run Squid as a transparent proxy on a host other than the firewall.
providers_add=Add a new routing provider.
providers_none=No routing providers have been defined yet.
providers_0=Name
providers_1=Number
providers_2=Mark
providers_3=Interface
providers_4=Gateway
providers_name=Provider name
providers_number=Provider number
providers_mark=Mark number
providers_dup=Duplicate provider
providers_main=Main table
providers_iface=Network interface
providers_gateway=Gateway router
providers_auto=Detect automatically
providers_opts=Additional options
providers_track=Track connections
providers_balance=Load-balance traffic
providers_fallback=Add provider to routing table
providers_loose=Allow traffic from firewall
providers_notrack=Turn of track
providers_tproxy=Support TProxy on lo interface
providers_edit=Edit Routing Provider
providers_create=Create Routing Provider
providers_header=Additional routing provider details
providers_copy=Copy routes through interfaces
providers_err=Failed to save routing provider
providers_ename=Missing or invalid provider name
providers_enumber=Missing or invalid provider number
providers_emark=Missing or invalid provider mark number
providers_edup=Missing provider to duplicate
providers_egateway=Missing or invalid gateway

manual_desc=This form can be used to manually edit the Shorewall file $1. Be careful, as no syntax checking will be done on the changes.
manual_reset=Undo
manual_err=Failed to save table file
manual_efile=Invalid table name!
manual_edata=No table file contents entered.

acl_nochange=Can apply, stop and start Shorewall configuration?
acl_files=Available Shorewall tables
acl_all=All
acl_sel=Selected below ..

delete_err=Failed to delete rows
delete_enone=No rows selected

opts_routeback=Accept traffic back to host
opts_source=Allow from host to any destination
opts_dest=Allow to host from any source
opts_critical=Always allow traffic between firewall
opts_maclist=Compare against MAC list?
opts_norfc1918=Reject private IP packets
opts_blacklist=Reject packets on blacklist
opts_tcpflags=Check for illegal TCP flags
opts_nosmurfs=Check for broadcast source packets
opts_ipsec=IPsec zone
opts_routefilter=Enable anti-spoofing route filtering
opts_logmartians=Log packets with impossible sources
opts_proxyndp=Enable proxy NDP
opts_ndp_filter=Only respond to NDP requests for interface IP
opts_detectnets=Taylor zone to include only routed hosts
opts_upnp=Remap packets via UPNP

opts_dhcp=Interface uses DHCP
opts_forward=Set forwarding
opts_ignore=Ignore up/down events
opts_optional=Interface is optional
opts_required=Interface is required
opts_bridge=Interface is a bridge

comment_add=Add a new comment.
comment_edit=Edit Comment
comment_create=Create Comment
comment_header=Table comment details
comment_msg=Message
comment_err=Failed to save comment
comment_enone=No message entered

log_create_table=Added entry to the $1 table
log_modify_table=Modified entry in the $1 table
log_delete_table=Deleted entry from the $1 table
log_deletes_table=Deleted entries from the $1 table
log_up_table=Moved up entry in the $1 table
log_down_table=Moved down entry in the $1 table
log_manual_table=Manually edited the $1 table file
log_create_comment=Added comment to the $1 table
log_modify_comment=Modified comment in the $1 table
log_delete_comment=Deleted comment from the $1 table
log_stop=Stopped firewall
log_start=Started firewall
log_refresh=Refreshed firewall
log_restart=Restarted firewall
log_clear=Cleared firewall

shorewall_conf_title=Master configuration file
shorewall_conf_desc=This page allows you to configure the global configuration variables.  NOTE: Changing the order of variables here is not recommended if you wish to preserve the relative position of comments in the configuration file.
shorewall_conf_add=Add a new configuration variable.
shorewall_conf_none=No shorewall6 configuration found.
shorewall_conf_0=Variable
shorewall_conf_1=Value
shorewall_conf_2=Comment
shorewall_conf_return=configuration variables list
shorewall_conf_edit=Edit configuration variable
shorewall_conf_create=Create configuration variable
shorewall_conf_header=Configuration variable details
shorewall_conf_err=Failed to save configuration variable
shorewall_conf_varname=Invalid variable name (must be a valid shell variable name)

params_title=Custom parameters
params_desc=This page allows you to configure Shorewall's custom parameters.  NOTE: Changing the order of parameters here is not recommended if you wish to preserve the relative position of comments in the configuration file.
params_add=Add a new custom parameter.
params_none=No custom parameters found.
params_0=Parameter
params_1=Value
params_2=Comment
params_return=custom parameters list
params_edit=Edit custom parameter
params_create=Create custom parameter
params_header=Custom parameter details
params_err=Failed to save custom parameter
params_varname=Invalid parameter name (must be a valid shell variable name)
__norefs=1